RFS Hydraulics

Plumbing & Sanitary

plumbing-sanitary

Pipe Coupling

pipe-coupling

Spanners & Sockets

spanners-sockets

Spanner Sets

spanner-sets

T handle tap wrenches

t-handle-tap-wrenches

Rfs Brass 10mm Od X 10mm Od Union Coupling Compression Fittings, Light Series F-D-B-U-10L

Compression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation.  To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule union coupling helps to attach and detach pipes without leaving deformities. It has three parts which are the male end, sleeve and nut. 

Series	: L (Light Series) & S (Heavy Series)

Working Pressure (bar)	: L series (160-315) & S series (315-800)

Material Standard	: DIN 2353 / DIN EN 3851 / ISO 8434-1

Step 1: Cutting ring and nut to be placed over the tube in the correct direction.

Step 2: Insert tube into pre-assembly tool up to tube abutment and tighten with the nut.

Step 3: Tighten 1 ¼ turns beyond the hand tighten position by using a wrench.

Step 4: Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface.

Step 5: With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

<h3 class="md-block-header-three">Rfs Brass 10mm Od X 10mm Od Union Coupling Compression Fittings, Light Series F-D-B-U-10L</h3>Union CouplingCompression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation. To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule union coupling helps to attach and detach pipes without leaving deformities. It has three parts which are the male end, sleeve and nut. About Union CouplingSize	: 6mm to 42mmSeries	: L (Light Series) &amp; S (Heavy Series)Working Pressure (bar)	: L series (160-315) &amp; S series (315-800)Material	: BrassMaterial Standard	: DIN 2353 / DIN EN 3851 / ISO 8434-1DIN Fittings installation guidelines:Step 1: Cutting ring and nut to be placed over the tube in the correct direction.Step 2: Insert tube into pre-assembly tool up to tube abutment and tighten with the nut.Step 3: Tighten 1 ¼ turns beyond the hand tighten position by using a wrench.Step 4: Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface.Step 5: With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

<h3>Rfs Brass 10mm Od X 10mm Od Union Coupling Compression Fittings, Light Series F-D-B-U-10L</h3>
Union Coupling
Compression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation. To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule union coupling helps to attach and detach pipes without leaving deformities. It has three parts which are the male end, sleeve and nut.&nbsp;
About Union Coupling
Size	: 6mm to 42mm
Series	: L (Light Series) &amp; S (Heavy Series)
Working Pressure (bar)	: L series (160-315) &amp; S series (315-800)
Material	: Brass
Material Standard	: DIN 2353 / DIN EN 3851 / ISO 8434-1
DIN Fittings installation guidelines:
Step 1: Cutting ring and nut to be placed over the tube in the correct direction.
Step 2: Insert tube into pre-assembly tool up to tube abutment and tighten with the nut.
Step 3: Tighten 1 ¼ turns beyond the hand tighten position by using a wrench.
Step 4: Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface.
Step 5: With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

AF Hydro

Oleo Tecnica

BOTHWELL

LAME

Stauff

Others

MJ Technos

LY Metal

Flanges

Pipe Clamps

Ferrule Fittings

Pipe Adaptor

Pipe Elbow

Pipe Nipple

Pipe Tee

Camlock Fittings

Copper Tubing

Kelvin How

buyerIntroduction

Rfs Brass 10mm Od X 10mm Od Union Coupling Compression Fittings, Light Series

rfs brass 10mm od union coupling compression fittings, light series seri ringan f-d-b-u-10l pipe kopling pipa hydraulics loyang kelengkapan mampatan gandingan kesatuan, siri paip hydraulics/rfs 液压 黄铜 联管接头压缩接头，轻型系列

rfs-brass-10mm-od-x-10mm-od-union-coupling-compression-fittings-light-series

Made of chrome vanadium steel,chrome-plated, sliding T-handle with long socket 

<h3 class="md-block-header-three">M10 005-480-11 TH-11L 11MM T Shape Wr </h3><ul class="md-block-unordered-list-item"><li>Made of chrome vanadium steel,chrome-plated, sliding T-handle with long socket </li><li>Size: 11</li><li>Length x Handle (mm): 310 x 190</li></ul>

<h3>M10 005-480-11 TH-11L 11MM T Shape Wr&nbsp;</h3>
<ul>
<li>Made of chrome vanadium steel,chrome-plated, sliding T-handle with long socket&nbsp;</li>
<li>Size: 11</li>
<li>Length x Handle (mm): 310 x 190</li>
</ul>

Wing Poh Hardware

BONDHUS

HOZELOCK

KNIPEX PLIERS

SABOTEN GARDEN TOOLS

SUNFLAG

KTC KYOTO TOOL

TAJIMA TOOLS

GEARWRENCH

WERA TOOLS

Sockets

Combination Spanners

Ring Spanners

Impact Sockets

Hole Saws

Drill Bits & Drill Bit Sets

Open End Spanners

Screwdrivers

Hex Keys & Sets

Garden Watering System

Sales

M10 005-480-11 TH-11L 11MM T Shape Wr

m10 005-480-11 th-11l 11mm shape wr bentuk handle tap wrenches

m10-005-480-11-th-11l-11mm-t-shape-wr

M10 005-054-711 11LRW 11PC Gear Ratchet Wrench Set

 Non-reversible type, flat panel handle, chrome-vanadium steel, mirror polish finish ANSI standard 

11 pcs:  3/8”, 7/16”, 1/2”, 9/16”, 5/8”,  11/16”, 3/4”, 13/16”, 7/8”,  15/16”, 1” (inch) 

<h3 class="md-block-header-three">M10 005-054-711 11LRW 11PC Gear Ratchet Wrench Set</h3> Non-reversible type, flat panel handle, chrome-vanadium steel, mirror polish finish ANSI standard 11 pcs: 3/8”, 7/16”, 1/2”, 9/16”, 5/8”, 11/16”, 3/4”, 13/16”, 7/8”, 15/16”, 1” (inch)

<h3>M10 005-054-711 11LRW 11PC Gear Ratchet Wrench Set</h3>
&nbsp;Non-reversible type, flat panel handle, chrome-vanadium steel, mirror polish finish ANSI standard&nbsp;
11 pcs: 3/8”, 7/16”, 1/2”, 9/16”, 5/8”, 11/16”, 3/4”, 13/16”, 7/8”, 15/16”, 1” (inch)&nbsp;