RFS Hydraulics

Plumbing & Sanitary

plumbing-sanitary

Pipe Elbow

pipe-elbow

Rfs Brass 8mm Od X 3/8" Male Npt 90 Degree Elbow Compression Fittings, Light Series F-D-B-L90M-N-08L-06

What Is compression DIN fittings – 90D Male Elbow

Compression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation.  To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule 90-degree male elbow combines pipes together at a 90-degree angle. One end is compression and the other is male NPT thread. It is most suitable to connect pipes where a turn of direction is needed in the flow of the system. 

Size	: 6mm to 25mm & 1/8” to 1”
Series : L (Light Series) & S (Heavy Series)
Working Pressure (bar) : L series (160-315) & S series (315-630)
Material : Brass
Material Standard : DIN 2353 / DIN EN 3851 / ISO 8434-1
Connection type : NPT / BSPP / BSPT

Step 1 : Cutting ring and nut to be placed over the tube in the correct direction.
Step 2 : Insert tube into pre-assembly tool up to tube abutment and tighten with the nut.
Step 3 : Tighten 1 ¼ turns beyond the hand tighten position by using a wrench.
Step 4 : Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface.
Step 5 : With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

<h3 class="md-block-header-three">Rfs Brass 8mm Od X 3/8&quot; Male Npt 90 Degree Elbow Compression Fittings, Light Series F-D-B-L90M-N-08L-06</h3>What Is compression DIN fittings – 90D Male ElbowCompression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation. To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule 90-degree male elbow combines pipes together at a 90-degree angle. One end is compression and the other is male NPT thread. It is most suitable to connect pipes where a turn of direction is needed in the flow of the system. About 90 D Male ElbowSize	: 6mm to 25mm &amp; 1/8” to 1” Series : L (Light Series) &amp; S (Heavy Series) Working Pressure (bar) : L series (160-315) &amp; S series (315-630) Material : Brass Material Standard : DIN 2353 / DIN EN 3851 / ISO 8434-1 Connection type : NPT / BSPP / BSPTDIN Fittings installation guidelines:Step 1 : Cutting ring and nut to be placed over the tube in the correct direction. Step 2 : Insert tube into pre-assembly tool up to tube abutment and tighten with the nut. Step 3 : Tighten 1 ¼ turns beyond the hand tighten position by using a wrench. Step 4 : Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface. Step 5 : With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

<h3>Rfs Brass 8mm Od X 3/8" Male Npt 90 Degree Elbow Compression Fittings, Light Series F-D-B-L90M-N-08L-06</h3>
What Is compression DIN fittings – 90D Male Elbow
Compression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation. To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule 90-degree male elbow combines pipes together at a 90-degree angle. One end is compression and the other is male NPT thread. It is most suitable to connect pipes where a turn of direction is needed in the flow of the system.&nbsp;
About 90 D Male Elbow
Size	: 6mm to 25mm &amp; 1/8” to 1” 
Series : L (Light Series) &amp; S (Heavy Series) 
Working Pressure (bar) : L series (160-315) &amp; S series (315-630) 
Material : Brass 
Material Standard : DIN 2353 / DIN EN 3851 / ISO 8434-1 
Connection type : NPT / BSPP / BSPT
DIN Fittings installation guidelines:
Step 1 : Cutting ring and nut to be placed over the tube in the correct direction. 
Step 2 : Insert tube into pre-assembly tool up to tube abutment and tighten with the nut. 
Step 3 : Tighten 1 ¼ turns beyond the hand tighten position by using a wrench. 
Step 4 : Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface. 
Step 5 : With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

AF Hydro

Oleo Tecnica

BOTHWELL

LAME

Stauff

Others

MJ Technos

LY Metal

Flanges

Pipe Clamps

Pipe Coupling

Ferrule Fittings

Pipe Adaptor

Pipe Nipple

Pipe Tee

Camlock Fittings

Copper Tubing

Kelvin How

buyerIntroduction

Rfs Brass 8mm Od X 3/8" Male Npt 90 Degree Elbow Compression Fittings, Light Series

rfs brass 8mm od 3/8" male npt 90 degree elbow compression fittings, light series f-d-b-l90m-n-08l-06 pipe pipa siku hydraulics loyang kelengkapan mampatan lelaki darjah, siri ringan paip hydraulics/rfs 液压 黄铜 毫米外径 外螺纹 度弯头压缩接头，轻型系列

rfs-brass-8mm-od-x-3-8-male-npt-90-degree-elbow-compression-fittings-light-series

Rfs Brass 22mm Od X 1/2" Male Npt 90 Degree Elbow Compression Fittings, Light Series F-D-B-L90M-N-22L-08

<h3 class="md-block-header-three">Rfs Brass 22mm Od X 1/2&quot; Male Npt 90 Degree Elbow Compression Fittings, Light Series F-D-B-L90M-N-22L-08</h3>What Is compression DIN fittings – 90D Male ElbowCompression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation. To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule 90-degree male elbow combines pipes together at a 90-degree angle. One end is compression and the other is male NPT thread. It is most suitable to connect pipes where a turn of direction is needed in the flow of the system. About 90 D Male ElbowSize	: 6mm to 25mm &amp; 1/8” to 1” Series : L (Light Series) &amp; S (Heavy Series) Working Pressure (bar) : L series (160-315) &amp; S series (315-630) Material : Brass Material Standard : DIN 2353 / DIN EN 3851 / ISO 8434-1 Connection type : NPT / BSPP / BSPTDIN Fittings installation guidelines:Step 1 : Cutting ring and nut to be placed over the tube in the correct direction. Step 2 : Insert tube into pre-assembly tool up to tube abutment and tighten with the nut. Step 3 : Tighten 1 ¼ turns beyond the hand tighten position by using a wrench. Step 4 : Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface. Step 5 : With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

<h3>Rfs Brass 22mm Od X 1/2" Male Npt 90 Degree Elbow Compression Fittings, Light Series F-D-B-L90M-N-22L-08</h3>
What Is compression DIN fittings – 90D Male Elbow
Compression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation. To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule 90-degree male elbow combines pipes together at a 90-degree angle. One end is compression and the other is male NPT thread. It is most suitable to connect pipes where a turn of direction is needed in the flow of the system.&nbsp;
About 90 D Male Elbow
Size	: 6mm to 25mm &amp; 1/8” to 1” 
Series : L (Light Series) &amp; S (Heavy Series) 
Working Pressure (bar) : L series (160-315) &amp; S series (315-630) 
Material : Brass 
Material Standard : DIN 2353 / DIN EN 3851 / ISO 8434-1 
Connection type : NPT / BSPP / BSPT
DIN Fittings installation guidelines:
Step 1 : Cutting ring and nut to be placed over the tube in the correct direction. 
Step 2 : Insert tube into pre-assembly tool up to tube abutment and tighten with the nut. 
Step 3 : Tighten 1 ¼ turns beyond the hand tighten position by using a wrench. 
Step 4 : Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface. 
Step 5 : With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

Rfs Brass 22mm Od X 1/2" Male Npt 90 Degree Elbow Compression Fittings, Light Series

rfs brass 22mm od 1/2" male npt 90 degree elbow compression fittings, light series f-d-b-l90m-n-22l-08 pipe pipa siku hydraulics loyang kelengkapan mampatan lelaki darjah, siri ringan paip hydraulics/rfs 液压 黄铜 22 毫米外径 外螺纹 度弯头压缩接头，轻型系列

rfs-brass-22mm-od-x-1-2-male-npt-90-degree-elbow-compression-fittings-light-series

Rfs Brass 10mm Od X 1/4" Male Npt 90 Degree Elbow Compression Fittings, Light Series F-D-B-L90M-N-10L-04

<h3 class="md-block-header-three">Rfs Brass 10mm Od X 1/4&quot; Male Npt 90 Degree Elbow Compression Fittings, Light Series F-D-B-L90M-N-10L-04</h3>What Is compression DIN fittings – 90D Male ElbowCompression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation. To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule 90-degree male elbow combines pipes together at a 90-degree angle. One end is compression and the other is male NPT thread. It is most suitable to connect pipes where a turn of direction is needed in the flow of the system. About 90 D Male ElbowSize	: 6mm to 25mm &amp; 1/8” to 1” Series : L (Light Series) &amp; S (Heavy Series) Working Pressure (bar) : L series (160-315) &amp; S series (315-630) Material : Brass Material Standard : DIN 2353 / DIN EN 3851 / ISO 8434-1 Connection type : NPT / BSPP / BSPTDIN Fittings installation guidelines:Step 1 : Cutting ring and nut to be placed over the tube in the correct direction. Step 2 : Insert tube into pre-assembly tool up to tube abutment and tighten with the nut. Step 3 : Tighten 1 ¼ turns beyond the hand tighten position by using a wrench. Step 4 : Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface. Step 5 : With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

<h3>Rfs Brass 10mm Od X 1/4" Male Npt 90 Degree Elbow Compression Fittings, Light Series F-D-B-L90M-N-10L-04</h3>
What Is compression DIN fittings – 90D Male Elbow
Compression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation. To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule 90-degree male elbow combines pipes together at a 90-degree angle. One end is compression and the other is male NPT thread. It is most suitable to connect pipes where a turn of direction is needed in the flow of the system.&nbsp;
About 90 D Male Elbow
Size	: 6mm to 25mm &amp; 1/8” to 1” 
Series : L (Light Series) &amp; S (Heavy Series) 
Working Pressure (bar) : L series (160-315) &amp; S series (315-630) 
Material : Brass 
Material Standard : DIN 2353 / DIN EN 3851 / ISO 8434-1 
Connection type : NPT / BSPP / BSPT
DIN Fittings installation guidelines:
Step 1 : Cutting ring and nut to be placed over the tube in the correct direction. 
Step 2 : Insert tube into pre-assembly tool up to tube abutment and tighten with the nut. 
Step 3 : Tighten 1 ¼ turns beyond the hand tighten position by using a wrench. 
Step 4 : Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface. 
Step 5 : With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

Rfs Brass 10mm Od X 1/4" Male Npt 90 Degree Elbow Compression Fittings, Light Series

rfs brass 10mm od 1/4" male npt 90 degree elbow compression fittings, light series 1/4 "male pipe pipa siku hydraulics loyang kelengkapan mampatan lelaki darjah, siri ringan paip hydraulics/rfs 液压 黄铜 外径 外螺纹 度弯头压缩接头，轻型系列

rfs-brass-10mm-od-x-1-4-male-npt-90-degree-elbow-compression-fittings-light-series

Rfs Brass 18mm Od X 1/2" Male Npt 90 Degree Elbow Compression Fittings, Light Series F-D-B-L90M-N-18L-08

<h3 class="md-block-header-three">Rfs Brass 18mm Od X 1/2&quot; Male Npt 90 Degree Elbow Compression Fittings, Light Series F-D-B-L90M-N-18L-08</h3>What Is compression DIN fittings – 90D Male ElbowCompression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation. To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule 90-degree male elbow combines pipes together at a 90-degree angle. One end is compression and the other is male NPT thread. It is most suitable to connect pipes where a turn of direction is needed in the flow of the system. About 90 D Male ElbowSize	: 6mm to 25mm &amp; 1/8” to 1” Series : L (Light Series) &amp; S (Heavy Series) Working Pressure (bar) : L series (160-315) &amp; S series (315-630) Material : Brass Material Standard : DIN 2353 / DIN EN 3851 / ISO 8434-1 Connection type : NPT / BSPP / BSPTDIN Fittings installation guidelines:Step 1 : Cutting ring and nut to be placed over the tube in the correct direction. Step 2 : Insert tube into pre-assembly tool up to tube abutment and tighten with the nut. Step 3 : Tighten 1 ¼ turns beyond the hand tighten position by using a wrench. Step 4 : Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface. Step 5 : With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

<h3>Rfs Brass 18mm Od X 1/2" Male Npt 90 Degree Elbow Compression Fittings, Light Series F-D-B-L90M-N-18L-08</h3>
What Is compression DIN fittings – 90D Male Elbow
Compression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation. To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule 90-degree male elbow combines pipes together at a 90-degree angle. One end is compression and the other is male NPT thread. It is most suitable to connect pipes where a turn of direction is needed in the flow of the system.&nbsp;
About 90 D Male Elbow
Size	: 6mm to 25mm &amp; 1/8” to 1” 
Series : L (Light Series) &amp; S (Heavy Series) 
Working Pressure (bar) : L series (160-315) &amp; S series (315-630) 
Material : Brass 
Material Standard : DIN 2353 / DIN EN 3851 / ISO 8434-1 
Connection type : NPT / BSPP / BSPT
DIN Fittings installation guidelines:
Step 1 : Cutting ring and nut to be placed over the tube in the correct direction. 
Step 2 : Insert tube into pre-assembly tool up to tube abutment and tighten with the nut. 
Step 3 : Tighten 1 ¼ turns beyond the hand tighten position by using a wrench. 
Step 4 : Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface. 
Step 5 : With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

Rfs Brass 18mm Od X 1/2" Male Npt 90 Degree Elbow Compression Fittings, Light Series

rfs brass 18mm od 1/2" male npt 90 degree elbow compression fittings, light series f-d-b-l90m-n-18l-08 pipe pipa siku hydraulics loyang kelengkapan mampatan lelaki darjah, siri ringan paip hydraulics/rfs 液压 黄铜 18 毫米外径 外螺纹 度弯头压缩接头，轻型系列

rfs-brass-18mm-od-x-1-2-male-npt-90-degree-elbow-compression-fittings-light-series

Rfs Brass 6mm Od X 1/4" Male Npt 90 Degree Elbow Compression Fittings, Light Series F-D-B-L90M-N-06L-04

Size	: 6mm to 25mm & 1/8” to 1” 
Series : L (Light Series) & S (Heavy Series) 
Working Pressure (bar) : L 
series (160-315) & S series (315-630) 
Material : Brass Material 
Standard : DIN 2353 / DIN EN 3851 / ISO 8434-1 
Connection type : NPT / BSPP / BSPT

Step 1 : Cutting ring and nut to be placed over the tube in the correct direction. 
Step 2 : Insert tube into pre-assembly tool up to tube abutment and tighten with the nut. 
Step 3 : Tighten 1 ¼ turns beyond the hand tighten position by using a wrench. 
Step 4 : Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface. 
Step 5 : With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

<h3 class="md-block-header-three">Rfs Brass 6mm Od X 1/4&quot; Male Npt 90 Degree Elbow Compression Fittings, Light Series F-D-B-L90M-N-06L-04</h3>What Is compression DIN fittings – 90D Male ElbowCompression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation. To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule 90-degree male elbow combines pipes together at a 90-degree angle. One end is compression and the other is male NPT thread. It is most suitable to connect pipes where a turn of direction is needed in the flow of the system. About 90 D Male ElbowSize	: 6mm to 25mm &amp; 1/8” to 1” Series : L (Light Series) &amp; S (Heavy Series) Working Pressure (bar) : L series (160-315) &amp; S series (315-630) Material : Brass Material Standard : DIN 2353 / DIN EN 3851 / ISO 8434-1 Connection type : NPT / BSPP / BSPTDIN Fittings installation guidelines:Step 1 : Cutting ring and nut to be placed over the tube in the correct direction. Step 2 : Insert tube into pre-assembly tool up to tube abutment and tighten with the nut. Step 3 : Tighten 1 ¼ turns beyond the hand tighten position by using a wrench. Step 4 : Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface. Step 5 : With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

<h3>Rfs Brass 6mm Od X 1/4" Male Npt 90 Degree Elbow Compression Fittings, Light Series F-D-B-L90M-N-06L-04</h3>
What Is compression DIN fittings – 90D Male Elbow
Compression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation. To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule 90-degree male elbow combines pipes together at a 90-degree angle. One end is compression and the other is male NPT thread. It is most suitable to connect pipes where a turn of direction is needed in the flow of the system.&nbsp;
About 90 D Male Elbow
Size	: 6mm to 25mm &amp; 1/8” to 1” 
Series : L (Light Series) &amp; S (Heavy Series) 
Working Pressure (bar) : L 
series (160-315) &amp; S series (315-630) 
Material : Brass Material 
Standard : DIN 2353 / DIN EN 3851 / ISO 8434-1 
Connection type : NPT / BSPP / BSPT
DIN Fittings installation guidelines:
Step 1 : Cutting ring and nut to be placed over the tube in the correct direction. 
Step 2 : Insert tube into pre-assembly tool up to tube abutment and tighten with the nut. 
Step 3 : Tighten 1 ¼ turns beyond the hand tighten position by using a wrench. 
Step 4 : Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface. 
Step 5 : With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

Rfs Brass 6mm Od X 1/4" Male Npt 90 Degree Elbow Compression Fittings, Light Series

rfs brass 6mm od 1/4" male npt 90 degree elbow compression fittings, light series f-d-b-l90m-n-06l-04 pipe pipa siku hydraulics loyang kelengkapan mampatan lelaki darjah, siri ringan paip hydraulics/rfs 液压 黄铜 毫米外径 外螺纹 度弯头压缩接头，轻型系列